Install Shower Head

How to Install a New Shower Head?

Changing a shower head is not rocket science. You only need to turn it in an anticlockwise direction to loosen it or clockwise to tighten it. You can get a pair of slip-joint pliers or an adjustable wrench to get rid of the old head.

You will need a rubber or plastic washer for sealing, instead of the silicone sealant or plumbers tape. It is important to consult the manufacturer’s manual to get the best outcome. The type of head you have will determine the installation process to follow, and here are some common types.

Fixed Shower Head


This type of shower head is not adjustable but fixed to the ceiling or wall with the aid of a pipe or directly. It is available in various styles and shapes with ½ inch connection. Also, you can’t adjust its pipe or hose because it is fixed or hidden.

Riser Rail and Head


You will find this type in a powerful electric shower. The head works as an over-bath shower before moving up the wall with the aid of the riser rail.

Bath Shower Mixer Taps


The bath shower mixer comes with a bath tap diverter to accommodate a hand shower. It is a space saver, and very popular in times past.

Power Showers


Power showers are very popular in places with low water pressure because they boost water flow. Fitting a power shower is a bit complex, hence, you may need to call a professional. If you want to do it on your own, you will need to get the electricity to the perfect place.

Also, power showers may not be your best bet if you want to conserve water. You can go for a shower with a lower flow rate if you want to reduce your energy bills.

Installing New Fixtures


You can lay your hands on many videos online teaching the steps for changing your shower head. If you will be replacing other fittings of your shower, you need to be careful especially if you will be drilling into walls. If you are not careful, the drill may scratch the fittings as well as fixtures.

You can choose among the various head types available, especially ones that fit in perfectly with your system. Changing a head is a stroll in the park, and if you also change the hose, the whole system will look as new.

Step-by-step Guide


Before going ahead with the installation process, you should take note that the maximum water flow according to state regulations is 2.5 gallons per minute (GPM) at 80 pounds per square inch (PSI). Also, you should consult with your user manual so that you will be able to get the best result.

What You’ll Need


You'll Need

To get the installation right you will need soft jaw pliers or soft cloth, an old toothbrush or wire brush, ladder or step stool, adjustable wrench, thread-sealing tape, and the shower head replacement.

Step 1: Turn Off the Faucet


You should not try removing the shower head when the faucet is on. This will make water to fill your bathroom, and this will be a total mess. Turn off the water faucet, and there is no need to disconnect the main water supply to the house.

Step 2: Unscrew the Current Shower head


You will need a wrench to remove an old corroded shower head. Turn the neck in an anticlockwise direction for perfect removal.

You should avoid turning the pipe in the wall so as not to spoil it. You can hold the connecting pipe with a soft cloth or soft-jaw pliers while turning the shower head by hand if it is a necessity.

Step 3: Get Rid of Excess Dirt


When you get rid of the obsolete showerhead, there may be some dirt on the extension pipe’s threaded end. Clean it up with an old toothbrush or a wire brush. Make sure that the thread is dry before you use the thread tape.

Step 4: Apply the Thread-Sealing Tape


Thread-Sealing Tape

Make sure that the threads are properly covered with the thread-sealing tape. You must ensure that every layer covers half of the preceding layer during the wrapping process.

The wrapping process should start at the base, and in a clockwise direction. Keep it going round up till the time that you will get to the threads’ extreme. Do not wrap anti-clockwise because the tape will unfold when you twist in the brand-new shower head.

If you are stuck along the way, take off the tape, and get a longer piece to start all over again. Use your thumb and forefinger to smoothen the tape into the threads.

Step 5: Connect the New Shower head


You need to read the manufacturer’s instructions before connecting the new shower head. If a product does not require a wrench for installation, and you use it, it may end up spoiling it.

Hand screw the showerhead in a clockwise direction to the threads. As soon as it is secure, use your hand to tighten it properly. Do not overtighten it so that you won’t break the plastic connecting nut.

Step 6: Check Fit and Look for Leaks


Tilt the showerhead away from you and put on hot and cold water. Search properly for any leakage so that you can fix it instantly. You may need to retighten it if you discover any leakage.

Besides, the tape on the threads should be enough, and there should be adequate firmness of the tape on the threads. The rubber seal needs proper checking to be sure that it lines up adequately or damaged.

Step 7: Fix or Make Adjustments


If there are issues with your connection, make sure you fix them. Observe the seal properly, and if necessary, apply new tape before thorough retightening. If the connecting nut is still leaking, there may be damage to one of the units.

If you discover that the water pressure is low, you should take off the showerhead and check it properly. Some parts may not be in their usual place, which requires fixing. Furnitureandhome UK provides additional information that will help you to get it right in terms of new shower head installation.

Leave a Reply

Your email address will not be published. Required fields are marked *